Installation steps
Keyboard Wedge Model:
Step 1 Turn the computer system power
off, and unplug
the keyboard cable.
Step 2 Connect the keyboard cable into
the short-cable
of the Reader.
Step 3 Connect the long-cable of the
Reader into the
keyboard socket on the computer system.
Step 4 Turn the computer system power
on, then you
can hear a beep sound for confirming the
reader's self-test, and green LED will be
lit to
indicate that the reader is ready for
operation.
Reader's Programming/setting
Note :
1. Suggest doing the programming/setting
under
Windows system
2. All settings should be done through
RS-232 COM port,
so the RS-232 model can be set directly
through its
installation.
3. To do the programming/setting of
keyboard wedge or
USB models, please refer to the
Installation Steps of
RS-232 model, using the bundled RS-232
extended
cable and PS/2 power adapting cable to do
the setting
through RS-232 port.
4. After programming/setting, install
back the keyboard
wedge or USB extended cable to the
reader.
Insert the TMSR bundled CD into the CD
drive
of your computer system. Then execute
"SETUP.EXE." to setup the program.
To run the program "MMSR" that you just
installed. You will see the following
screen:
Step 1
Step 2
RS-232 Model:
Step 1 Turn the computer power off.
Step 2 Connect the Reader's cable to
the RS-232 COM
port on the computer.
Step 3 Connect the DC-plug of 5V DC
power adapter to
the DC jack on the cable-end of the
Reader, you
can hear a beep sound for confirming the
Reader's self-test, and the green LED on
the
Reader will be lit to indicate that the
Reader is
ready for operating.
Step 4 Turn the computer power on, and
run your
application software, include one RS-232
drive
utility, to get the data from the serial
port which
connects the Reader.
USB Model:
Step 1 To make sure the Windows USB
utility is
available in your computer.
Step 2 Connect the Reader to the USB port
on the
computer, you can hear a beep sound for
confirming the Reader's self-test, and
the green
LED on the Reader will be lit to indicate
that the
Reader is ready for operating.
1.
the setting options are as following
01 Device selection for KB interface
only available for KB interface
02 Intercharacter delay
select KB or RS-232 setting, then the
delay time
for intercharacter to match the sending
speed.
03 Language for keyboard interface
select one language
04 Terminator
select one instruction following the data
string
06 Preamble and postamble
set the preamble and postamble characters
attached to the data string
08 RS-232 parameters
-to select the RS-232 parameters
SETTING:
16 General parameters
to setup the data output mode and beep
sound
19-1 Magnetic parameters
to setup the track data sequence and
magstripe
format
19-2 Magnetic parameters
to setup the start/end sentinel
2.
COM port selecting
to select COM1 or COM2 port
3.
to store the setting inside the Reader.
4.
to set the Reader as default setting.
5.
to list or print the setting result.
6.
to load the setting data to computer.
7.
to save the setting data into an indicated file.
8.
to exit from the setting program.
9.
to display all present settings.
The Reader's setting procedure:
1. Select "SETTING" first, and setup all
the parameters
as you want.
2. Go to "SELECT", to select a COM port
that connects
the Reader.
3. Click "SEND", to store the settings
inside the Reader
and finish the setting.
SELECT:
SEND:
DEFAULT:
PRINT:
LOAD:
SAVE:
EXIT:
Setting Overview:
Step 3
3
4
5
(Suggest to do the programming/setting
under Windows system)
to PC Keyboard port
USB port
AC power
source
RS-232 port
