TYSSO MSE-630 Magnetic Stripe Card Encoder Manual

Install MSE Utility and USB Driver Electrical Interconnections Mechanical Environmental Performance There are two subfolders on the utility/driver CD: MSE Utility and USB Driver. Run Setup.exe from the MSE Utility folder and follow the instructions to complete the utility installation. Windows will prompt you to install a device driver for the newly detected hardware when you plug in the USB cable to your host PC the first time. Specify the path to the USB Driver folder and Windows will complete the driver installation in a few seconds. You only need to run the driver installation once. Windows will load the USB driver automatically the next time around. Note that USB driver assigns a virtual serial port for communications. Control Panel > System > Hardware > Device Manager > Ports (COM & LPT) will lead you to identify the port number. 100~240VAC/+24VDC 2.5A RS-232 (Default: 9600 baud, odd parity, 7 data bits) or USB (via USB serial conversion) 350mA (read), 600mA (write) DB9F with molded 2.1mm power jack TXD (2), RXD (3), ground (5), CTS (7), RTS (8) ABS (optional metal available) Manual, single direction 8.2" L x 2.5" W x 2.5" H (208m 64mm 64mm) 1.8lbs (0.8kg) 0 C~40 C, 20%~90%RH, non-condensing -20 C~70 C, 20%~90%RH, non-condensing 1,000,000 passes for both read and write heads 5~50IPS (read), 5~30IPS (write) 300~4000 Oersted (read), 300~4000 Oersted (write) 0.010~0.080" (0.25mm~2.03mm) 30% (210BPI) or 40% (75BPI) at 10~40IPS <0.5% (read), <0.75 (write) 95,000 hours (Power Off/Auto Shutoff) Power Supply Interface Current Consumption Cabling Pin Assignment (DB9F) Casing Swipe Dimensions Weight Operating Temperature Storage Temperature Media Life Media Speed Media Coercivity Media Thickness Low Amplitude Reading Error Rate MTBF 4. Specifications 1 2 3 1. Introduction 2. Installation MSE-630A reads and writes magstripe cards with coercivity ranging from 300 through 4000 Oersted. It is intended for use with a personal computer via the RS- 232 or USB connectivity. MSE-630A reads and writes data format as specified by ISO 7811/2 through 5 and ANSI 4.16 1983. Any ISO/ANSI standard track format can be read/written from/to any track location (1, 2, or 3). MSE-630A also reads and writes custom data format and offers a selectable writing density (75/210 BPI) through the host commands (see "Command Set" section of this document). Standard MSE-630A package comes equipped with the following: MSE-630A reader/writer hardwired with RS-232 serial cable Switching power supply (100~240VAC input/+24VDC 2.5A output) USB adapter cable Utility/driver CD Two blank magstripe cards (one hi-co and one lo-co) User's Manual Follow the steps below to interconnect MSE-630A to your PC: 1. Power off your PC. 2. Connect DB9F end of RS-232 cable to a free serial port on your system. 3. Connect power plug of AC adapter to power jack on RS-232 cable. 4. Connect AC adapter to electrical outlet. 5. Power on your PC. Upon successful installation of MSE-630A, All three LEDs (red, yellow, and green) will come on simultaneously for a couple of seconds and only the green LED will stay on. MSE-630A beeps momentarily. Hi-co/lo-co setting is configurable at startup. 3. MSE Utility About MSE Utility MSE Utility is a productivity tool intended primarily for use with ISO/ANSI-compliant magstripe cards. ISO or ANSI specifies 7 bits per character as the standard data format for track 1, and 5 bits per character for both track 2 and track 3. ISO or ANSI also specifies 210 BPI as the encoding density for tracks 1 and 3, and 75 BPI for track 2. We use ISO, ANSI, or ISO/ANSI interchangeably throughout this document. In addition to Keyed-in Encode, MSE Utility also supports Copy Encode, File Encode, and Incremental Encode as shown by the main menu below: MSE Utility also provides support for non-ISO/ANSI card reading and writing. What follows is a dialog box for the user to specify the data format for each track to work with.

Next Page >>

PDF Version | Product Specifications | Operation Guide | Software Utility

Home | Products | Contact