Transmit data from host
Interface conversion
Transmit data from printer
2. Installation
A. RS-232 Connection:
Step1: Power off the computer system.
Step2: Connect the VFD 1615 Display Cable to
the RS-232
Port of the computer.
Step3: Proper set the connection between the
bundled Power
kit and the Switch power supply inside the
computer
or connecting the DC power source by the
appropriate
DC power Adapter.
Step4: Turn on the computer, the VFD 1615
Display will
show its default settings (Character set, Baud
rate,
page code, etc) and ready for receiving data
To RS-232 port
AC power
Source
Extension
RS-232 Cable
-4-
-5-
data for printer
B.
Pass-through Connection:
Step 1: Power off the computer, printer and
display.
Step 2: Please refer to the interface section
of the manual for
detailed information of the cable, and make
proper
connection to appropriate ports of the devices.
Step 3: Power on the computer, printer and
display.
Step 4: The devices are ready for working.
Note: All the data transmitted from Host
will be processed
by peripheral device selection command, then
transmit
the data to the proper devices, either the
printer or the
display.
3. Interfaces
A. RS-232 Cable-end
B. DC Power Jack
DSUB-9
Pin Female
Connector
2
3
5
7
8
9
1
4
6
TX
RX
GND
CTS
RTS
VCC
Short Connection
+
GND
9~12VDC/500~1000 mA
9
5
6
1
C.
Pass-through Cable Pin-outs:
CBL-VFD-PASS 1
CBL-VFD-PASS 2
For the printer with ESC commands
For the printer without ESC commands
DB9F
DB9M
DB9M
DB9F
DB9M
DB9M
To:Host
To:Printer
To:Display
To:Host
To:Printer
To:Display
2 (RXD)
2 (TXD)
3 (TXD)
3 (RXD)
3 (RXD)
4 (DTR)
4 (DSR)
5 (GND)
5 (GND)
6 (RXD)
6 (DSR)
6 (DTR)
7 (RTS)
7 (CTS)
8 (CTS)
8 (RTS)
2 (RXD)
2 (TXD)
3 (RXD)
3 (TXD)
3 (TXD)
3 (RXD)
4 (DTR)
4 (DSR)
5 (GND)
5 (GND)
5 (GND)
6 (DSR)
6 (DTR)
7 (RTS)
7 (CTS)
8 (CTS)
8 (CTS)
6 (DTR)
4 (DSR)
To: PC
1800mm
300mm
To: Display
To: Printer
DB 9M
DB 9F
DB 9M
-7-
-6-
-9-
-8-
4. Installing Configuration Utility
Before running the bundled RS-232 setting
software, please
note the following default values:
Com port:
1
Baud rate:
9600
Parity:
none
Data bit:
8
1. Insert the bundled CD disc into the CD-ROM
drive
2. Run the "setup.exe" file from the disc.
3. Follow the installation hints until the
installation process is
fully completed.
4. Go "start menu" > "programs" > "VFD-1615" >
"VFD1615"
to begin the customer display configuration.
Click the
RS-232 tab (see pictures) from the menu to set the
Com Port, Baud Rate, Data Bit and Parity
setting.
Note: In order to successfully change to new
settings, please
check if the Current Setting on the utility
program
matches the actual current setting of VFD 1615
Display
unit.
RS-232 Setting:
When configuration is successfully done:
When configuration isn't successfully done:
An "OK" message box will be shown on the
monitor.
Click it or press "enter" at the keyboard then
the Display
content will be cleared.
A "Device Time Out" message box will be shown
on the
monitor. Please do the configuration again or
consult with your
supplier for further assistance.
PDF Version
|
Previous Page
| Next Page
::
Customer Display FAQ
:: PDF
brochure
:: Specification
:: Software Download
Customer Display
Index:
VFD |
LCD |
Arabic & Chinese Display |
Double Side Display
TYSSO
Product Links:
Barcode Scanner |
Magstripe Card Reader
/ Writer |
POS Customer Display |
POS Keyboard
Touchscreen POS System
| Cash Drawer |
Serial-Ethernet
Converter | Links to Other Sites |
Receipt Printer
www.barcode-manufacturer.com
