2. Quick Start
2.1) Unpacking & Parts Identification
a. Unpacking:
B. Parts Identification:
-5-
-4-
Printer cover
Open this cover to load
or replace paper.
Control
panel
Features LED indicators
to indicate printer
status and buttons to
operate the printer.
Front
cover
Cover
Open lever
Pull this lever in the
direction of the
arrow to open the
printer cover.
2.2) Loading the Paper Roll
a. Make sure that the paper roll matches the
printer's specification. Do not use
paper rolls that have the paper glued to the
core because the printer cannot
detect the paper end correctly.
b. Open the paper roll cover by pressing the
cover-open button
Important:
mportant:
The printing quality and lifespan of the
thermal head cannot be
guaranteed if any paper other than that
recommended is used. Thus,
the warranty will be void automatically if any
fault occurs due to
the use of wrong paper rolls.
I
Do not pull the cover open lever and open the
printer cover when
printing is in progress.
Recommended Paper Rolls
Part Number
Manufacturer
HPK-110
Hansol Patech Co. Ltd.
AF50KS-E
JUJO Paper Co. Ltd.
TF-50KS-E
Nippon Paper Industries Co. Ltd.
PD-160R
New Oji Paper Mfg. Co. Ltd.
F380
Nansaki Specialty Papers Inc.
Cover-Open lever
c. While observing the direction of the roll,
set the paper roll into the hollow, and
pull on the leading edge of the paper toward you
as shown:
d. Close the cover: When closing the cover,
press the center of printer cover
firmly to prevent paper miss-loading
-7-
-6-
e. Tear off the paper outside the cover as
shown.
3. Printer Interface and Connection
3.1) Connecting the Interface Cable
3.2) Connecting to a Cash Drawer
a. Before connecting/disconnecting the
interface cable, make sure that power
to the printer and all the devices connected to
the printer is turned off.
b. Connect the interface cable to the connector
on the rear panel of the printer.
c. In the case of a serial interface, tighten
the connector screws. In the case of a
parallel interface, fasten the connector clasps.
Important:
Make sure that the printer is turned off and
unplugged from the AC outlet
and that the computer is turned off before
making connections.
Do not connect a telephone line into the
peripheral drive connector. Failure
to observe this may result in damage to the
printer.
3.3) Connecting the AC Adapter
a. Connect the AC power cord to the inlet of
AC adapter, and then connect the
power cord plug to a suitable electrical
outlet.
b. Connect the adapter cable to power connector
of printer; make sure the
printer power switch is OFF before making any
connections.
c. Set the power switch as shown. The POWER
lamp on the control panel will
light up.
CAUTION:
DO NOT USE ANY AC POWER ADAPTERS OTHER THAN
SPECIFIED.
-9-
-8-
Plug the cable connector securely
into the printer's interface connector.
Attach the other end of the
cable to the computer
(Blue LED) The POWER light is on whenever
the printer is on.
(Red LED) This indicates printer online/offline
status or an error
(Button) Press the FEED button to feed roll
paper.
(Button) Press the ONLINE button to set printer
ONLINE/OFFLINE
4. Configuration
Printer Control Panel & Status Indication
4.1) Panel LED indicators
a. PRP-080I
(Standard)
Printer Status (Red LED)
Red light ON: Indicates that the printer is
online.
Red light OFF: Indicates that the printer is
offline.
Red light flashes: Indicates the printer
error(s) such as out of paper, paper
jammed, or printer cover is not closed properly
1. Power (POWER) LED: Green
On:Power is stable
Off:Power is not stable
2. Error (ERROR) LED: Red
On: Off line (except during paper feeding
using the FEED button and
test printing, and the error state.)
Off: Normal condition
3. Paper roll end (PAPER OUT) LED: Red
On: The paper roll near end is detected.
Off: Paper is loaded (Normal condition).
b.
PRP-080II
(Advanced)
4.2) DIP Switch Settings
The DIP switch panel is locating at bottom of
the printer as shown:
SW-1
Select cutter
No
Yes
OFF
SW-2
Select beeper
Yes
No
OFF
SW-3
Print density
Dark
Light
OFF
SW-4
Two-byte character code
No
Yes
OFF
SW-5
Reserve
OFF
SW-6
Reserve
OFF
SW-7
Select Baud rate
OFF
SW-8
Select Baud rate
OFF
ON
ON
38400
OFF
ON
4800
ON
OFF
9600
OFF
OFF
19200
(*) Baud Rate is only available for serial
interface models.
a.
b.
Note:
PRP-080I
(Standard)
PRP-080II
(Advanced)
DIP Switch Functions:
Switch
Function
ON
OFF
Default
SW-7
SW-8
Baudrate(bps)
Before configure the DIP switch settings,
please first turn the printer
power off and remove the paper roll.
-11-
-10-
Switch Function
ON
OFF
Default
1
Baud Rate (*)
38400
19200
OFF
2
Auto Cutter
No
Yes
OFF
3
Color Deepness Deeper Normal OFF
4
Beep
Yes
No
OFF
DIP Switch Functions:
Previous
Page | Next
Page
PDF Version
|
POS Printer Index |
Specifications |
Product Index |
PRP-080
Standard/Basic
Barcode Scanner |
Magstripe Card Reader
/ Writer |
POS Customer
Display |
POS Keyboard
Touchscreen POS System | Cash Drawer
|
Serial-Ethernet Converter | Links to Other Sites
www.barcode-manufacturer.com
